ON Semiconductor MM74HC74AM

Lifecycle Status

ACTIVE (Last Updated: 4 days ago)

Factory Lead Time

51 Weeks

Contact Plating

Contact plating (finish) provides corrosion protection for base metals and optimizes the mechanical and electrical properties of the contact interfaces.

Tin

Mount

Surface Mount

Mounting Type

Surface Mount

Package / Case

14-SOIC (0.154, 3.90mm Width)

Number of Pins

14

Supplier Device Package

14-SOIC

Weight

240.999296mg

Clock-Edge Trigger Type

Positive Edge

Number of Elements

2

Operating Temperature

The operating temperature is the range of ambient temperature within which a power supply, or any other electrical equipment, operate in. This ranges from a minimum operating temperature, to a peak or maximum operating temperature, outside which, the power supply may fail.

-40°C~85°C TA

Packaging

Semiconductor package is a carrier / shell used to contain and cover one or more semiconductor components or integrated circuits. The material of the shell can be metal, plastic, glass or ceramic.

Tube

Series

74HC

Published

1999

Part Status

Parts can have many statuses as they progress through the configuration, analysis, review, and approval stages.

Active

Moisture Sensitivity Level (MSL)

1 (Unlimited)

Termination

SMD/SMT

Type

D-Type

Max Operating Temperature

The Maximum Operating Temperature is the maximum body temperature at which the thermistor is designed to operate for extended periods of time with acceptable stability of its electrical characteristics.

85°C

Min Operating Temperature

-40°C

Voltage - Supply

2V~6V

Frequency

72MHz

Base Part Number

74HC74

Function

Set(Preset) and Reset

Number of Outputs

4

Output Type

Differential

Polarity

Non-Inverting

Number of Channels

2

Voltage

5V

Number of Circuits

2

Max Supply Voltage

In general, the absolute maximum common-mode voltage is VEE-0.3V and VCC+0.3V, but for products without a protection element at the VCC side, voltages up to the absolute maximum rated supply voltage (i.e. VEE+36V) can be supplied, regardless of supply voltage.

6V

Min Supply Voltage

The minimum supply voltage (V min ) is explored for sequential logic circuits by statistically simulating the impact of within-die process variations and gate-dielectric soft breakdown on data retention and hold time.

2V

Output Current

The rated output current is the maximum load current that a power supply can provide at a specified ambient temperature. A power supply can never provide more current that it's rated output current unless there is a fault, such as short circuit at the load.

5.2mA

Number of Bits

2

Clock Frequency

94MHz

Propagation Delay

the flight time of packets over the transmission link and is limited by the speed of light.

110 ns

Quiescent Current

The quiescent current is defined as the current level in the amplifier when it is producing an output of zero.

4μA

Turn On Delay Time

Turn-on delay, td(on), is the time taken to charge the input capacitance of the device before drain current conduction can start.

12 ns

Logic Function

AND, D-Type, Flip-Flop

Current - Quiescent (Iq)

4μA

Number of Inputs

1

Number of Gates

The number of gates per IC varies depending on the number of inputs per gate. Two?input gates are common, but if only a single input is required, such as in the 744 NOT(or inverter) gates, a 14 pin IC can accommodate 6 (or Hex) gates.

2

Number of Bits per Element

1

Max Frequency

28MHz

Max Propagation Delay @ V, Max CL

19ns @ 6V, 50pF

Trigger Type

Positive Edge

High Level Output Current

High-level Output Current IOH The current flowing into the output at a specified high- level voltage. Low-level Output Current IOL The current flowing into the output at a specified low- level output voltage.

-5.2mA

Input Capacitance

The capacitance between the input terminals of an op amp with either input grounded. It is expressed in units of farads.

5pF

Low Level Output Current

The current into the output terminal with input conditions applied that, according to the product specification, will establish a low level at the output.

5.2mA

Number of Input Lines

1

Number of Output Lines

1

Height

1.5mm

Length

8.75mm

Width

4mm

REACH SVHC

No SVHC

Radiation Hardening

Radiation hardening is the process of making electronic components and circuits resistant to damage or malfunction caused by high levels of ionizing radiation, especially for environments in outer space (especially beyond the low Earth orbit), around nuclear reactors and particle accelerators, or during nuclear accidents or nuclear warfare.

No

RoHS Status

RoHS means “Restriction of Certain Hazardous Substances” in the “Hazardous Substances Directive” in electrical and electronic equipment.

ROHS3 Compliant

Lead Free

Lead Free